Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Kitchen Remodeling: The Austin Owner’s Guide
Unilock kitchen remodeling in Austin typically runs $14,000 – $45,000 installed, depending on the material, layout changes, and whether we’re replacing one failed component or rebuilding the whole kitchen. If your Unilock paver or wall unit has cracked, shifted, or separated from the substrate, we can match the replacement and rebuild the surrounding kitchen surfaces so the fix looks original. Most Austin owners discover the problem after a season of heavy rain or foundation movement: a paver edge lifts, a wall unit pulls away from the cabinet line, or grout around the Unilock surface starts crumbling faster than it should.
We’re Sawyer Remodel Austin, an independent remodeling contractor in Austin, not affiliated with Unilock directly. What that means for you: we match the product, order the right replacement, and install it to the original spec, all with a written price before we pick up a tool.
Key takeaways:
- Installed Unilock kitchen remodeling in Austin runs $14,000 – $45,000, with isolated component replacement starting lower.
- We match Unilock series compatibility before ordering anything, so you don’t end up with a color or size mismatch.
- Written price first, photo updates during the job, and a 365-Day Done Right Promise on the work.
- Call (409) 834-4854 for a free Austin estimate.
Which Unilock Models This Applies To
Unilock doesn’t make kitchen cabinets or countertops in the traditional sense, but its paver, wall, and stone veneer lines show up constantly in Austin kitchen remodels, especially in outdoor kitchens, kitchen backsplashes, accent walls, and floor transitions. The compatibility question matters because Unilock runs multiple series: Richcliff, Thornbury, Brussels Block, Courtstone, and the Estate line each have different surface textures and joint widths. A Richcliff paver pulled from one batch won’t always sit flush against a Courtstone unit, even if the color name sounds close.
Before we order a replacement, we check the stamp on the back or underside of the existing unit, measure the joint width, and match the manufacturing lot code when we can. If the original is a discontinued color or series, we’ll tell you straight, then offer the closest current match or a compatible aftermarket paver that won’t look like a patch job. For an Austin kitchen remodel, the OEM-vs-aftermarket call depends on whether the failed piece is structural (floor paver, supporting wall) or decorative (backsplash veneer). We lean OEM on structural work because the tolerances and freeze-thaw ratings are proven for Texas heat and rain cycles.
Styles & brands we work with
Signs Your Unilock Kitchen Remodeling Is Failing
- Edge lifting or rocking underfoot. The base beneath the paver has washed out or compacted unevenly. In Austin’s clay-heavy soil, this is one of the most common failures we see in kitchens with paver flooring. The paver isn’t usually broken; the base is.
- Cracks running through multiple units in a line. That line usually follows a slab seam or a settling area. When the substrate moves, the pavers move with it, and the crack pattern tells us where the movement started.
- Joint sand or grout washing out fast. If you’re sweeping sand or crumbling grout every few weeks, water is channeling through the joints. This accelerates paver movement and invites mold under the surface.
- Wall units separating from the cabinet or wall line. A gap opening up behind a Unilock veneer or accent wall usually means the adhesive bond has failed or the wall behind it is shifting. Left alone, the gap widens and the units can drop.
- White haze or efflorescence that won’t clean off. Efflorescence is the mineral deposit left behind when water moves through the unit and evaporates. Persistent efflorescence in an Austin kitchen means moisture is coming through from behind or below, not just surface humidity.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
The full Unilock kitchen remodel in Austin runs $14,000 – $45,000. That covers the tear-out, substrate repair, new Unilock or Unilock-compatible materials, edging, joint sand, sealing where needed, and cleanup. An isolated repair, like replacing a run of failed backsplash veneer or a section of paver flooring, lands on the lower end or below that range because we’re not rebuilding the room.
What drives the price: how much structural repair the base needs, whether we’re matching a discontinued series, whether the kitchen is indoors or outdoors, and how much cutting around cabinets and appliances is required. Every Austin estimate from us includes the parts, labor, haul-away, and the written warranty on our work. No change orders at the door. The number we give you is the number you pay. Call (409) 834-4854 and we’ll put it in writing.
DIY or Call Us?
If you notice a loose paver or crumbling grout, you can safely document the damage, check whether the unit is stamped with a series name, and keep water away from the area until we arrive. That’s about where the safe DIY line ends. The danger is not the paver itself; it’s what you can’t see underneath. Pulling units without checking for gas lines, water lines, or electrical conduit running through the kitchen subfloor is how a small repair becomes a five-figure fix. In Austin kitchens, we’ve found irrigation lines and electrical runs directly beneath failed paver sections more times than we can count.
If the unit is on a wall or supporting any weight, don’t touch it. Call us at (409) 834-4854 and we’ll come assess the failure, match the part, and give you a written price. Luca Romano reads a floor plan fast and calls out problems before demo starts, because fixing sloppy work costs everybody money. Measure twice, cut once, then we actually build the thing.
FAQs
Properly installed Unilock pavers and wall units in Austin typically last 20 to 30 years before the base or substrate needs major work. Texas heat accelerates surface wear and clay soil movement shortens base life compared to cooler, more stable-soil regions. If your surface failed in under 10 years, the install or the base is usually the culprit, not the product. Call (409) 834-4854 and we’ll tell you what’s actually going on under the surface.
Yes, isolated repairs are common when the base is still sound and the damage is confined to a few units. If the failure runs across a slab seam or the base has washed out, a patch job will fail again within a season or two. We’ll give you an honest recommendation either way and a written price before any work starts.
A full Unilock kitchen remodel in Austin typically takes 2 to 5 weeks depending on the size of the space, structural repairs needed, and material lead times. An isolated replacement like a backsplash section or a small paver run can often be done in 1 to 3 days. We’ll give you a schedule in writing before the project starts, and you’ll get photo updates as the work progresses.
We keep common Unilock series colors and joint materials on the truck for quick repairs and match the rest to your existing lot code. If your series is discontinued or your lot is out of production, we source the closest compatible match and confirm the color and texture with you before installing. Call (409) 834-4854 and we’ll check availability for your specific unit before we even schedule the visit.
If your Unilock kitchen surface is failing, don’t wait until the edge lifts enough to trip someone. Call Sawyer Remodel Austin at (409) 834-4854 for a free estimate. We’ll match the part, write the price down, and keep you posted with photos until the job is done right.
Written by Luca Romano, Owner, Sawyer Remodel Austin at Sawyer Remodel Austin, serving Austin and nearby areas.
